Product Description
 |
 |
 |
 |
Key Features
• HDMI in & HDMI out with re-clocking and equalisation
• Relay momentary or latching control
• Assignable relays triggered on signal presence or via RS-232
• Breakout of source audio via mirrored S/PDIF and stereo mini-jack
• In-line EDID manager with assignable presets or copy & import capability
HDMI In-line Signal Re-Clocker with EDID Management, Automatic or Manual CEC, Audio De-embed and Relay Triggering
A multi-purpose installer tool, the CON-H2-EDID can perform a variety of tasks within an install. As an in-line device, it can act as an EDID manager to request specific content from a source, or as an audio de-embedder, extracting HDMI source audio via the S/PDIF or stereo mini-jack ports. Additionally, it can be a micro zone controller, sending CEC and RS-232 power triggers to connected projectors or screens and from its two relay ports, and can trigger devices in the zone using signal presence logic.
IN-LINE EDID EMULATOR
In a legacy installation scenario where EDID is not being communicated properly, the CON-H2-EDID can be connected in-line after the source device and using either a built-in or uploaded EDID file, can ensure the correct content is requested from the source.
AUDIO DE-EMBED
Compatible with any current content thanks to its 18Gbps and HDCP2.2 support, it can be placed in-line after any source device and extract the incoming audio via the 3.5mm jack or coaxial S/PDIF port.
MICRO ZONE CONTROLLER
Working on signal presence logic, the CON-H2-EDID can trigger a connected screen or projector on/off via both CEC or RS-232; the RS-232 commands can be entered via the configuration s/w tool that is part of WMS v1.6. Additionally, at the same time, it can trigger 3rd party motors (projector screens, lifts, blinds & curtains) via the built-in relays
HDMI2.0 MAXED OUT
Sporting an 18Gbps HDMI input, the CON-H2-EDID can support all UHD video signals up to and including 2160p 4:4:4/60, and high frame-rate HDR 12bit 4:2:2 up to 60Hz.
Features
- HDMI in & HDMI out with re-clocking and equalization (HDMI range extender)
- Breakout of source audio via mirrored S/PDIF and stereo mini-jack
- In-line EDID manager with assignable presets or copy & import capability
- Assignable relays triggered on signal presence or via RS-232
- Source sensing power triggering:
- CEC: Compatible screens or projectors triggered manually via API or automatically on signal presence
- Serial: Power on/off commands can be stored and sent via RS-232 port
- Setup & configuration via simple PC configuration tool (WyreStorm Management Suite v1.6 or higher)
- Relay momentary or latching control
- Powered by 12v DC power supply (US, UK, EU and AU PSU pins included)
- Mounting brackets included
- USB-3-pin phoenix cable required for setup (not included) – Use P/n CAB-USB-PX1
Specifications
| Audio and Video | |||
| Inputs | 1x HDMI in: 19-pin type A | ||
| Outputs | 1x HDMI Out: 19-pin type A 1x Audio Out: 3.5mm (1/8in) TRS Stereo 1x S/PDIF Out: S/PDIF Coaxial Digital |
||
| Audio Formats | HDMI Pass-through 2ch PCM | Multichannel: LPCM and Up to DTS-X and Dolby Atmos S/PDIF Out: De-Embed: 2ch PCM | Multichannel: Up to 5.1 DTS and Dolby Digital Analog Out: 2ch |
||
| Video Resolutions (Max) |
|
||
| Supported Standards | DCI | RGB | HDR | HDR10 | Dolby Vision | HLG | BT.2020 | BT.2100 | ||
| Maximum Pixel Clock | 600MHz | ||
Communication and Control |
|||
| HDMI | HDMI 2.0 | HDCP 2.2 | EDID | CEC Triggering Inputs supports DVI/D and DisplayPort Dual-Mode (DP++) v1.3 with adapter (not included) |
||
| CEC | CEC Power Triggering | Requires CEC compatibility | ||
| RS-232 | 1x RS-232: 3-pin Terminal Block - 3.5mm | ||
| Relays | 1x Relay 2: 3-pin Terminal Block - 3.5mm | 1x Relay 1: 3-pin Terminal Block - 3.5mm | Max 1A load | ||
Power |
|||
| Power Supply | 12V DC 0.5A | ||
| Max Power Consumption | <2W | ||
Environmental |
|||
| Operating Temperature | 32°F ~ 113°F (0°C ~ 45°C) | 10% ~ 90%, non-condensing | ||
| StorageTemperature | -4°F to ~ 158°F (-20°C ~ +70°C) | 10% ~ 90%, non-condensing | ||
| Maximum BTU | 7 BTU/hr | ||
Dimensions & Weight |
|||
| Rack Units/Wall Box | <1U | ||
| Height | 20mm/0.79in | ||
| Width | 120mm/4.73in | ||
| Depth | 80mm/3.15in | ||
| Weight | 0.23kg/0.51lbs | ||
Regulatory |
|||
| Safety and Emission | CE | FCC | RoHS | RCM | ||
What's In The Box
- 1x Main unit
- 1x DC 12V 1A Power Supply (US/UK/EU/AU)
- 3x 3-Pin Terminal Block
- 2x Mounting Brackets
- 1x Quick Start Guide
